nice! Try add another strips![]()
Hi all,
Just sharing the lighting for my new set up (4ft by 13ft by 14ft high) with mainly short hairgrass and some rock scape.
The lighting consists of two strips of 7020 LED Rigid Strip which come in slim aluminum profile, that I just need to rest both ends on top of the tank and they seat about 1 inch above the water line.
I remove the frosted pvc cover to allow more lights to reach the bottom.
Each 4 ft strip cost $20 without 12V power supply. Unfortunately, the shop owner at Sim Lim Square was not able to provide more details except that they are white 7020 chip and each metre of strip draws 24 Watt of power.
I'm now seeing tiny bubbles from the plants so the lighting level should be enough (?) but the normal glass tank now look slightly bluish under the light even it suppose to be "white".
The concern is how whether the strip will be corroded due to proximity to the water surface, if so I may put back the frosted cover or get some clear acylic sheet, and aso the color temperature will suit the plant.
nice! Try add another strips![]()
Nicethe strip will not corrode have been using about the same setup for 6months now. Just have to be careful during maintenance to keep it dry. Also do not move it abt too much as the soldering might be broken
Thanks Chong99 , must say I was inspired by your DIY led postings before embarking on this lighting set up.
As the power supply I have is only for 5A , two strip of 1.2m each would be pushing the limit at around 57.6W(/12v=4.8A).
Will monitor the plant grow for the moment. (can't wait for the hair grass to form a thick carpet though, only if constantly looking at them helps!)
Check out my Blog on planted tank, good for newbies ( i am lazy to retype all the info i know, so please click and read below link... i hope you don't fall asleep while reading)
Link to my Blog
I am not PERFECT but I am LIMITED EDITION !!!BIG Tank comes with BIG Responsibility...as they makan a lot of $$....lol
When lights are labelled as "white" it can span a very wide range of color temperatures and spectrums. It'll be a good idea to try and find out the actual color temperature and spectrum of those lights (since they were not specifically designed for planted tanks), at least you may be able to get a better understanding of how your plants will respond in terms of their growth pattern.
Planted tank owners usually prefer to have a light which has a balanced proportion of red and blue spectrums (different spectrums promote different types of plant growth). Most of the time aquarium companies try to create their lights with combinations of such favorable spectrums that plants can utilize efficiently, yet still look pleasing to the user's eyes.
Its still okay to use lights that are heavier on the blue spectrum though... just that for planted tanks, it may alter the visual color tone of the plants and fishes, so everything looks more bluish, similar a marine tank.
For reference, here is some useful info on lighting spectrums and their relationships to plant photosynthesis: http://www.aquaticplantcentral.com/f...osythesis.html
Thanks UA! The reference was really very technical .
After reading your reference, was contemplating on adding red LED (like Chong99's set) until discovering the ADA write up on their LED. It seems there are different views on optimum lights for aquarium plants until now?
But from your reference, I found useful that algae needs longer stretch of continuous light than plants, so I will be doing a 4 hour full light (as I read reference in Robertus's website that plant needs at least 4 hours of continuous light to be effective) and 1 hour break , follow by another 4 hour light. The 1 hour break will have the surrounding ceiling light in the office so it will not be in total darkness.
The ADA writeup is similar to what other brands also practice too... nowadays they all design their planted tank lights around a spectrum chart with more blue (for better water depth penetration), some red/orange and a tiny bit of green (to balance out the overall color tone so that the tank doesn't look too blue).
I guess while just having only blue spectrum is okay for growing plants, most people also want to view their plants and fishes in a more "realistic" color environment, hence a mix of different spectrums is used to create a balanced color rendition.
In many of the higher-end LED lights for planted tanks (ie. MaxSpect Razor), they arrange a ratio of different color LED clusters to create that balance.
Maybe you can try mixing in abit of other LEDs in your setup, see if it balances out the color (so that the tank looks less blue and more natural white). With DIY LED solutions, you have the flexibility of experimentation and customization.
Yeah, the "siesta regimen" is a common method to give plants abit more advantage over algae, it may not generate a significant difference but it could help in some setups.
Just have to note that if you are injecting a higher amount of Co2 into the tank, it would be a good idea to also schedule the Co2 injection to be off during the break period too, so that the Co2 levels don't accumulate to excessive levels when the plants are not photosynthesizing (its mainly for the safety of the tank's livestock).
Hi,
Thanks. you are on right track
For selecting power supply, always keep some margin of 30%~40% from the rating indicated in the spec. This is to prolong the life of the adapter. I always using 60~70% of the rating...
Another way is check the temperature of the adapter with your handit should be warm hot but not burning hot...
If your light really operate at 4.8A, the adapter won't last long...
The actual power consumption of your light may not be at max rating because in DC power system, there is always voltage drop along the wires and how you led strips are connected (series or parallel).
cheers.
Hi can I check which floor of sim lim sq did you buy it from? I'm looking for them too (:
Sent from my iPhone using Tapatalk
I've got them from Suang Huat Heng E &E Trading #02-68 SL Sq. The shop owner can do soldering to extend the strip and wiring as well.
Last Saturday, I realize the shop next to it has Rigid strip with clear pvc cover instead of frosted , unfortunately the chips are of 5050 type.
Im there right now haha.. He said he doesn't have 4ft only 1m for $15. But he assured that it is in fact enough coverage for a 4ft tank so I'm taking his word for it haha
Sent from my iPhone using Tapatalk
Last edited by Johnenrui; 8th Jun 2015 at 15:35.
I bought extra length of 200mm of strip and aluminum and ask him to soldier the strip . The aluminum I join by screw so that I can have total 1200mm and have both end seated on the tank.
Sent from my iPhone using Tapatalk
I understand thanks a lot man! But I only bought 1 strip hopefully it's enough haha.. If it isn't I will go down to get one more.. Did you "waterproof" the ends?
Sent from my iPhone using Tapatalk
No sir, end caps are provided with the aluminum
Sent from my iPhone using Tapatalk
Hahaha I should be calling you sir. Thank you so much for your replies! They didn't give me end caps![]()
Sent from my iPhone using Tapatalk
ImageUploadedByTapatalk1433852775.622357.jpg
Added 1 RGB strip , just to satisfy itchy finger syndrome
Sent from my iPhone using Tapatalk
Woah the difference it makes is astounding.. The blue really brings out a depth in the scape! You got the strip from the same shop?
Sent from my iPhone using Tapatalk
Bookmarks