Advertisements
Aquatic Avenue Banner Tropica Shop Banner Fishy Business Banner
Results 1 to 11 of 11

Thread: Oil layer on top

  1. #1
    Join Date
    Jun 2008
    Location
    eastside
    Posts
    76
    Feedback Score
    0
    Country
    Malaysia

    Oil layer on top

    Advertisements
    Fresh n Marine aQuarium Banner

    Advertise here

    Advertise here
    I've asked this before about getting rid of the oil layer. I took the suggestion of adding an air stone but some said it would encourage the growth of snails and algae? My tank only has moss-no plants.

    My 2ft tank is in a rather limited spaced shelf so I can't add anything other than an air stone. Is there a recommended timeframe or frequency that I can turn on the air stone?

    Thanks all!

  2. #2
    Join Date
    Oct 2008
    Posts
    315
    Feedback Score
    0
    Country
    Singapore

    Re: Oil layer on top

    You can turn on your air pump when your lights are off.

  3. #3
    Join Date
    Dec 2007
    Posts
    262
    Feedback Score
    0
    Country
    Singapore

    Re: Oil layer on top

    Are you running external filter? if yes, then adding a surface skimmer should do the job.

    I just replaced my external filter with an internal filter and is facing the same problem, what I did was to install a cheap HOB filter with built in surface skimmer and the problem is under control, only problem now is to monitor the CO2 loss.

    As for air stone, its is not advisable to add oxygen from an external source, but if you still going to do it, then as per Ghim's advise, turn it on when lights is off.

  4. #4
    Join Date
    Jun 2008
    Location
    eastside
    Posts
    76
    Feedback Score
    0
    Country
    Malaysia

    Re: Oil layer on top

    So I have to leave the airstone on overnight? Wow...my battery bill is gonna skyrocket! Hehe!

    I'm using an internal filter and there isn't much space to add a skimmer, unfortunately! What's this HOB filter you mention?

    Thanks guys!

  5. #5
    Join Date
    Nov 2006
    Posts
    857
    Feedback Score
    0
    Images
    1
    Country
    Singapore

    Re: Oil layer on top

    HOF is Hang on filter. Some of them comes with a skimmer which can suck the layer of protein. AS for air stone, actually you can on it for half an hour and via movement on the water surface, the oil would disperse.

  6. #6
    Join Date
    Mar 2009
    Posts
    180
    Feedback Score
    0
    Country
    United_States

    Re: Oil layer on top

    The issue is related to a lack of surface agitation. What you're seeing on the surface is a collection of oils and proteins that normally should be emulsed in to the water. It is a sign of poor surface agitation, which means less oxygen exchange. If there's any way you can disrupt the surface of the water more, it will help to reduce the appearance of this film, and improve the health of your aquarium.

    -Philosophos

  7. #7
    Join Date
    Sep 2008
    Posts
    18
    Feedback Score
    0
    Country
    Singapore

    Re: Oil layer on top

    Do you think shrimps will get sucked into the surface skimmer? Anyone have experienced? Thanks for sharing.

    Regards

  8. #8
    Join Date
    Jun 2008
    Location
    eastside
    Posts
    76
    Feedback Score
    0
    Country
    Malaysia

    Re: Oil layer on top

    Thanks, Philosophos. So there's no hard and fast rule for keeping the air stone on then? Will experiment on that! Cheers, guys!

  9. #9
    Join Date
    Mar 2009
    Posts
    55
    Feedback Score
    0
    Country
    United_States

    Re: Oil layer on top

    Depends on if it is a harmful oil that was introduced to the tank by outside means, which is rare, rather than it just being a protein layer accumulating on the surface. Agitating it will only disperse it and prevent it from being visible and preventing oxygen exchange at the surface. It most likely is just protein; in which case an increase in surface agitation is all you really need in a freshwater setup. If it was saltwater, you would need a surface skimmer. If your fish seem fine then I'd just increase agitation, as anything harmful should have already shown adverse effects on your fauna. Otherwise, there is one method I know of for removing harmful oils that accumulate at the surface, although I don't know if it's the most effective.

  10. #10
    Join Date
    Mar 2009
    Posts
    180
    Feedback Score
    0
    Country
    United_States

    Re: Oil layer on top

    For the air stone, it kind of depends. If you've got pressurized CO2, pumping a pile of air bubbles directly in to the water is going to gas off the CO2 faster than a surface ripple provided by a properly angled rain bar on a canister filter. So far, in my experience, shrimp and oto's won't care if the pH changes by .4 within about 12 hours. My guess is that some south american cichlids might not be so happy about that kind of change. In this case, using an air stone will depend on how high you want to turn your CO2 up to compensate, and what other fauna is going in the tank.

    If you're running DIY yeast based CO2, don't even think about an air stone. You can't turn it up, so what ever you can get is good; either get compressed CO2 or a new filter.

    In the case of no CO2 or just using excel, crank that airstone up 24/7; the only CO2 you're going to get is from the air, and you'll likely never get more than 5ppm.

    -Philosophos

    *edit* if you're using excel, consider dosing in the morning; glutaraldehyde will disappear within 12 hours, and the NH3 might go down with it. I've just started reading up on this chemical today.

  11. #11
    Join Date
    Dec 2007
    Posts
    262
    Feedback Score
    0
    Country
    Singapore

    Re: Oil layer on top

    Quote Originally Posted by newtank View Post
    Are you running external filter? if yes, then adding a surface skimmer should do the job.

    I just replaced my external filter with an internal filter and is facing the same problem, what I did was to install a cheap HOB filter with built in surface skimmer and the problem is under control, only problem now is to monitor the CO2 loss.

    As for air stone, its is not advisable to add oxygen from an external source, but if you still going to do it, then as per Ghim's advise, turn it on when lights is off.
    drop my idea of using HOB filter, the Co2 loss is too much. I am now using a internal filter and place the outlet right at the surface of the water to agitate the surface after lights off, tried for 2 days now, and working fine.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •