Advertisements
Aquatic Avenue Banner Tropica Shop Banner Fishy Business Banner
Results 1 to 4 of 4

Thread: Changes to Water Parameters

  1. #1
    Join Date
    Nov 2002
    Location
    Singapore
    Posts
    8
    Feedback Score
    0
    Country
    Singapore

    Changes to Water Parameters

    Advertisements
    Fresh n Marine aQuarium Banner

    Advertise here

    Advertise here
    Hi all,

    I have a 2 ft tank and all these while I am having very stable water parameters. It was PH 6.5-6.8 and a KH of 5.

    I did not measure the water for about 1 month. Recently, I started to measure again. Suprisingly, it became PH 7.2 - 7.4 and KH 8.

    CO2 rate has been quite constant at 1bps.

    Qns:
    1) What could lead to the PH & KH up?
    2) At that PH & KH level, what are the potential problems?
    3) How to bring it back to 6.5-6.8 and a KH of 5?

    Background info.

    Tank Size: 2 x 1 x 1.5ft (20Gallon)
    Lighting: 2 x 36W PL
    Filteration: Ehiem 2213
    CO2 : Cylinder 1bps

    Plants: DD, Riccia, E Quad, another 4 types dont know what name'

    Bioload: 20 Neon Tetra, 10 Cardinals, 10 Malayans, 5 Oto, 1 SAE.

    Thanks guys.

  2. #2
    Join Date
    Dec 2001
    Location
    Balestier
    Posts
    2,769
    Feedback Score
    0
    Country
    Singapore
    what may have happen is that you may have gotten some coral chips in your substrate or that your substrate is not lime free. The other could be you may have used rock pieces for deco and they are not lime free.

    Did you test your water KH? It could be that your tap water KH is high, so it may be a good idea for you to know your tap water KH level. Should it be hover at 8 to 8.5, leave it alone and deal with this level. It may not be such a good idea to lower the KH.

    At KH level of 8 is very decent for any planted tank and the corresponding PH should be around 6.7 to 6.9. try increasing the bps to 2 perhaps.
    [email protected]
    ----------------------------------------------------------
    The title below my name does not make me a guru...listen at your own risk!...

  3. #3
    Join Date
    Nov 2002
    Location
    Singapore
    Posts
    8
    Feedback Score
    0
    Country
    Singapore
    Thanks David.

    You may be right, I added a few more rocks recently.
    I will try removing them and test again.

    As for CO2 rate, bcos I am using a reactor (3 ball thingy), I find that increasing more CO2 does not give any corresponding returns. Because if I increase it to 2bps, the 3 balls will get stuck. When it stuck, I think the dissolving rate will slow down a lot. Even now I reduce it to 2 balls only, the dissolving speed is still limited.

  4. #4
    Join Date
    Nov 2002
    Location
    Singapore
    Posts
    1,229
    Feedback Score
    0
    Images
    38
    Country
    Singapore
    Just to add to what David left off.

    "I will try removing them and test again"
    KH 8 is not bad though 3~6 is ideal. Leave the rocks there, stop adding baking soda in your next water change and see what happen.
    The rock is giving you cheap Ca supply and some KH. Typically, it would give you about 3 KH and 4 GH.

    "I find that increasing more CO2 does not give any corresponding returns."
    If you need to pump anything more than 2 bubbles per second, you need to get the longer version of the reactor. I am using the longer version and I took out those balls (they are useless as they often get stuck and increase maintenance) and I have 4 bubbles per second without problem.

    Tips:
    You can transform this cheap reactor into external reactor by:
    1) sealing the joints with teflon tape, then,
    2) permanently joint the joints by super glue
    3) use cable ties to secure the hose onto the reactor.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •