Just Another Shrimp Tank (Beta)

[reiner09]

wa..really evil project it is.. 3 partition O.O ... will be interested in how your setup is going to be like

[Mafia00]

Evil project, can't wait to see your setup.

[Kenng]

These are the ones you are selling?

[eviltrain]

These are the ones you are selling?

yapz, these was the ones that i was selling.

[avex30]

hahaha i thot all already sold no stock? When have stock?? to stop my ranting of empty tank...

Planning to do a 3 hrs reset change some top soil out from lower tank kekekeke

[eviltrain]

hahaha i thot all already sold no stock? When have stock?? to stop my ranting of empty tank...

Planning to do a 3 hrs reset change some top soil out from lower tank kekekeke

now wait for the shrimplets to grow up lo. cannot sell them at 0.5cm mah. wait i tio complain.

wa, topping up with mosura soil?

[avex30]

now wait for the shrimplets to grow up lo. cannot sell them at 0.5cm mah. wait i tio complain.

wa, topping up with mosura soil?

nah left over africana hahahaha

[huizhong]

Wa 4tier 4ft setup? Power! Can't wait to see the whole setup so I can learn and copy. Hehe

[eviltrain]

Wa 4tier 4ft setup? Power! Can't wait to see the whole setup so I can learn and copy. Hehe

You saw before le lei. Hahaha.

Send from my GT-P1000 (Overcome 7 Series v4.0.0)

[godprint]

Can I copy here... Lol... But I think my floor will sink...

[darrentyl]

I don't mind if the price is alot cheaper...

now wait for the shrimplets to grow up lo. cannot sell them at 0.5cm mah. wait i tio complain.

wa, topping up with mosura soil?

[crescebi]

-how i fill the holes of the partition with super fine stainless steel mesh.-


victim - water purifier purchased at hardware shop ( there's 3-4 SS mesh in 1 water purifier )



The hole size is about 1 dollar gold coin size, the mesh is about 50cent coin size. i lay the acrylic partition flat on the floor and press the SS mesh thru it. After this i push the SS mesh out.



then i use this glue to go round the inside of the hole very carefully with paint brush very thinly in order not to mess the outside.

after this i lay the acrylic flat on the floor again to press the molded SS mesh into the hole again and let it air dry.



6/8 done ( because i never get enough water purifier )

-How i use air tube to hold the partition in place-



i used the soft type of air tube, cut to desired length ( my case is 28cm ) and slit one side from end to end.

slot the acrylic into the air tube ( if you wants, you can glue it with plastic glue )



almost end product~

-thanks for viewing-

HI, May I know if you have any pictures of the water purifier which you obtained the wire mesh from?
Thanks!

[Limy]

Hey Alan... wow... you made me miss my shrimps

[eviltrain]

Change project. Add 3 more 1feet gex tanks on the top.

Send from my GT-P1000 (Overcome 7 Series v4.0.0)

[eviltrain]

oh yah, forgot to add.

i got another set of SS pipe from bro Avex30 too. so this 3 tanks will be chilled by the ss pipe with chilled water inside.

[eviltrain]

HI, May I know if you have any pictures of the water purifier which you obtained the wire mesh from?
Thanks!

err, its sold at most hardware shop

Hey Alan... wow... you made me miss my shrimps

lai la~~ come back la~~

[eviltrain]

Update~~~





Send from my GT-P1000 (Overcome 7 Series v4.0.0)

[RonWill]

Nice rig!! You're not using insulating foam over those Gex tanks' J-tubes? Able to hold down the temp with additional SS extensions??

[eviltrain]

Nice rig!! You're not using insulating foam over those Gex tanks' J-tubes? Able to hold down the temp with additional SS extensions??

Yapz. Able to hold the temperature same throughout. I have upgraded my chiller from 150a to 300a. So far no problem.

Send from my GT-P1000 (Overcome 7 Series v4.0.0)

[darrentyl]

Nice work.

I also want to get a 3 tier stand..

Hehe..