Just another DIY ADA Cabinet build

[darter]

Hi bro,

very inspiring project. Are we able to get pre laminated ply? Thinking of doing one for my up coming 3 footer. Dont wish to get the ready made as my co told mi not to rush getting it setup. So with a very long time frame, i might dwell into doing it myself. Have you got the blue prints of the cab?

[neverwalkalone]

Thanks darter.

The only 'pre laminated' ply comes in white; single or double side - it's what you find commonly used in cupboard shelves. The trouble with that apart from not being very nice looking is that you'd still have to laminate the edges after cutting/fixing it up; so you're better off laminating the entire box with your choice of colour/design!

As for "blue prints" - I've listed in the very 1st post; it's in Russian, but you can easily figure it out.

Look forward to seeing your build too!

[limz_777]

did you use a pipe bender to bend the L shape ? what size stainless steel rod did you use ?

[Ark]

Nice diy! Thank for sharing too.

[neverwalkalone]

did you use a pipe bender to bend the L shape ? what size stainless steel rod did you use ?

Hi bro - sorry for late reply; it is not possible to bend stainless steel pipes with a pipe bender (ie DIY style). They were done by the pipe vendor; I believe they are 25mms (ODs).

Thanks for the encouragement Ark!

[planted86]

Hi neverwalkalone,

may i know what did u use to trim the laminate? a router?

[neverwalkalone]

@planted86 - the laminating process was shared in post #6 here. Basically, I used the Plastic cutter and then filed/sanded it down.

It's quite easy to do once you get the hang of it, but nevertheless I'm sure you'll get a better finish if you have the right (power) tools like routers etc as seen in so many DIY videos online.

[daniel19831123]

Just out of curiousity, how much did it cost to have the light stand produced by the pipe vendor and which vendor did you approach to fabricate the metal stand?

[neverwalkalone]

Just out of curiousity, how much did it cost to have the light stand produced by the pipe vendor and which vendor did you approach to fabricate the metal stand?

Sent you a PM.

[tobi]

can pm me as well? thanks.

[kanguin]

Hi can pm me where you get the light stand please.
THank you.

[mercur1al]

Very nice!

[Bieffe]

Swee.
would like to see the back. Did holes or slots for the pipes. No vents for chillers?
Can I read your LED diy guide?

[neverwalkalone]

Very nice!

Thank you!

Swee.
would like to see the back. Did holes or slots for the pipes. No vents for chillers?
Can I read your LED diy guide?

Thank you. Pardon the delay in replying, I havent been on the forum as much as I used to.

The photos of the back are in post #6. Repeated here:
IMG_0237.JPG

I don't use chillers (I don't have 24hr aircon, so I don't think my fishes/plants should have it too! ). Basically, 4 holes at the back, and 2 on the sides. The power cables and CO2 tube (used to) are via the back, the in/out water pipes are via the sides.

The LED build thread is here: http://www.aquaticquotient.com/forum...-for-3-ft-tank. There's been significant progress on LED light builds since then, I'm sure you can do better at a lower cost too!

[Bieffe]

Oh boy I missed that. Didn't use chiller until the plants keep dying. Your level of carpentry is commercial grade. Not to mention the tools u need to have to get such beautiful cuts and holes. Your work table is also great. If only I have luxury to such stuffs and space. What I did is I took an Ikea unit and mod...so to pass inspection by my CFO! Hahah. Hole saw also biggest is 63mm that size a 13amp cannot go through....so have to dismantle plugs.

[neverwalkalone]

Oh boy I missed that. Didn't use chiller until the plants keep dying. Your level of carpentry is commercial grade. Not to mention the tools u need to have to get such beautiful cuts and holes. Your work table is also great. If only I have luxury to such stuffs and space. What I did is I took an Ikea unit and mod...so to pass inspection by my CFO! Hahah. Hole saw also biggest is 63mm that size a 13amp cannot go through....so have to dismantle plugs.

You're too kind bro. The build 'looks good from FAR, but at near view is far from good!' hahaha

I don't have that many good tools really. Just a drill and a jig saw. Had to go to a carpenter to get the hinge recess (circular hole for the door hinges) drill with their tools. Pretty ex for a simple 5min job. No choice. I would have invested in a paddle/wood bit if I'd known the guy charged so much!

the 13amp power plug should be able to squeeze through the hole made with the 63mm hole saw.

Be careful with IKEA products, most of them are made from particle board, and it may not be very strong but more importantly, it gets damaged easily by water!! IKEA also sells solid wood (their 'as is' corner) but you'll have to cut them to your needs, so you're back to square 1 (their solid wood 'discards' are good value, but SUPER HARD to cut!)

Ya - most important is that the "CO" approves! You're a wise man.

[Bieffe]

Happy wife happy life. Ya took the ikea and reinforce here and there. Ya once u get water it will bubble! I once paid a shop to cut plywood $2 per cut! Gone in 30 sec!

[neverwalkalone]

Happy wife happy life. Ya took the ikea and reinforce here and there. Ya once u get water it will bubble! I once paid a shop to cut plywood $2 per cut! Gone in 30 sec!

A happy wife is a happy household. (heh heh).

Do share you build so we can all learn and appreciate!

[fai]

Hi bro, for the 2footer, do you still add kapur wood for support?

[neverwalkalone]

Hi, the 2fter doesn't have additional supports; the plywood is strong enough to support it without issues.