What I have is a powerhead 400L/hr to run my reactor (what 4 bioballs).






What I have is a powerhead 400L/hr to run my reactor (what 4 bioballs).



Hi Phil. What is your tank size? Able to share the pictures on the filter and reactor you are using?
Yeah, you need to match the reactor size with the filter flow rate (there are different sizes of reactors)... if the filter is too slow or BPS too high for the reactor size, then alot of CO2 will tend to build up, if the filter is too fast for the reactor size then alot of the Co2 will get flushed ineffectively out as bubbles. Hence getting the correct sized reactor for the canister filter flow rate is important.
Note that its actually okay for a small pocket of Co2 to accumulate at the top of the reactor, its just being progressively mixed and dissolved, so that there is zero wastage, rather than all that Co2 just coming out out the outflow and simply getting wasted at the water surface.
Instead of those older reactor designs that use tumbling plastic balls, you can look at the newer designs like the ISTA Mix Max, it uses a pair of inbuilt rotors/impellers (naturally powered by the filter's flow) which spin at high speed and chop up the pocket of Co2 gas into smaller bubbles for faster and more complete dissolve rate inside the reactor. It also comes in 2 sizes so you can pick the one which matches your filter flow rate (M-size is for 360-1,000 l/ph canister filters, L-size is for >1,000 l/ph canister filters)... here are what they look like:
Photo from Mizuworld.
Here is a demo video on how its setup and used:
With a properly functioning Co2 reactor, you may find that less BPS injection is required to achieve the optimal Co2 levels (due to its near 100% Co2 dissolve efficiency), hence that could save you $$$ on Co2 refills in the long run.![]()
Last edited by Urban Aquaria; 26th Oct 2014 at 14:30.
Btw... this is the version i use, its also from ISTA and works the same way as the Mix Max models, but uses the design of the Sera 500 model:
The advantage of this version is it comes with lock nuts to secure the hoses.
This reactor model is rated for 360-1,000 l/ph canister filters. This design doesn't have a larger version for higher flow-rate filters though, for those have to go for the L-size Mix Max model.
I run this Co2 reactor with a 750 l/ph Eheim Ecco Pro 300 canister filter at 0.5-1.0 BPS injection rate for a 2ft/64 liter planted tank, the Co2 drop checker is constantly at light green during active photoperiod, and plants pearling within 15 minutes of lights on.
Last edited by Urban Aquaria; 26th Oct 2014 at 14:33.





Mine is the sera reactor 500
http://m.petco.com/product/120388/Se...e-Reactor.aspx
Powered by my eheim 2217
More than enough power. But it is recently slowing down a little
Holy is the Lord, God Almighty ! The Earth is filled with His Glory !
90 x 50 x 50 cm tank: Eheim 2217; ANS CO2 Solenoid with 60mm intense bazooka; Zetlight 6400; Teco 500 Chiller; Borneo Wild Steel inlet/outlet
Ferts: Dry Mixture/Dr Mallicks. Temp: 26 degrees Substrate: ADA Amazonia





Mine is assembled the same way as urban aquaria. But his is much nicer in terms of placement. I leave mine on the floor of the cabinet hahah.
A very good reactor i must say. Results so far are good
Holy is the Lord, God Almighty ! The Earth is filled with His Glory !
90 x 50 x 50 cm tank: Eheim 2217; ANS CO2 Solenoid with 60mm intense bazooka; Zetlight 6400; Teco 500 Chiller; Borneo Wild Steel inlet/outlet
Ferts: Dry Mixture/Dr Mallicks. Temp: 26 degrees Substrate: ADA Amazonia




Thank you guys for the advise. I guess I've got to get this reactor. Will update you guys once I acquired it. Thanks again guys.



My is a overflow and sump system hence no canister filter to hook on. Need to get a pump to push the reactor. Based on my tank size what is the recommended pump and reactor size to use?
For your current 400 l/ph powerhead, the M-size model would be suitable.
Though a stronger powerhead (maybe 600-800 l/ph) would help dissolve the Co2 quicker as it spins the impellers faster to churn and chop up the bubbles.
If you upgrade to an even stronger powerhead with close to or higher than 1,000 l/ph flow rate, then the L-size version would work better.

Sorry to interrupt. A question, I understand that with a stronger flow rate the co2 will be dissolved better. However, won't that also cause stress to the fauna? Currently I have reduced the flow rate as my shrimps look like they are in a washing machine near the outlet![]()





By right the flow rate would reduce after passing through the reactor. That is why getting a little more powerful should be alright
Holy is the Lord, God Almighty ! The Earth is filled with His Glory !
90 x 50 x 50 cm tank: Eheim 2217; ANS CO2 Solenoid with 60mm intense bazooka; Zetlight 6400; Teco 500 Chiller; Borneo Wild Steel inlet/outlet
Ferts: Dry Mixture/Dr Mallicks. Temp: 26 degrees Substrate: ADA Amazonia
Yeah, it depends on your tank size and how your filter distributes the flow.
If higher flow rate filters are used and will be creating excessive flow, then you just need to find ways to slow down or baffle the flow at the output (while still retaining the high flow rate within the filter system)... either point the outflow towards hardscape or use larger diameter outputs.
One of the best ways (and also looks nice) is to use different shaped lily pipe outflows, like the "poppy" or "spin" type outflows, they redirect the flow upwards or sideways to spread out the flow and reduce the overall current.
Here are some examples of the poppy and spin lily pipe designs...
Photos from VIV website.





One tip though. I really hate using glass pipes now as i always have a hard time maintaining the inlet pipe. You can always get a double tap to reduce flow and also use stainless steel one. Sleek and does not expose the algae and bacteria
Holy is the Lord, God Almighty ! The Earth is filled with His Glory !
90 x 50 x 50 cm tank: Eheim 2217; ANS CO2 Solenoid with 60mm intense bazooka; Zetlight 6400; Teco 500 Chiller; Borneo Wild Steel inlet/outlet
Ferts: Dry Mixture/Dr Mallicks. Temp: 26 degrees Substrate: ADA Amazonia






Guys. Does it matter if I put it in my sump?
You can put the reactor outlet anywhere, the sump is fine too... just have to make sure the outflow in the main tank is creating a good circulation with minimal deadspots to get Co2 infused water effectively to as many planted areas of the tank as possible.
Btw, planted tanks that use sump filtration do tend to off-gas more Co2 due to the higher water agitation from the overflow and sump system. In addition, the larger combined water surface area of both the main tank and sump tank also contribute to increased rate of Co2 loss, hence its quite common that such setups usually require more Co2 to be injected in order to compensate for those effects.





Go to the LFS and tell them you want eheim double taps. Alternatively google eheim double tap and you get the idea.
Holy is the Lord, God Almighty ! The Earth is filled with His Glory !
90 x 50 x 50 cm tank: Eheim 2217; ANS CO2 Solenoid with 60mm intense bazooka; Zetlight 6400; Teco 500 Chiller; Borneo Wild Steel inlet/outlet
Ferts: Dry Mixture/Dr Mallicks. Temp: 26 degrees Substrate: ADA Amazonia
Bookmarks